Sale!

APM 2.8 ArduPilot UAV Flight Controller Ublox Neo-6M GPS PM 915Mhz 3DR Kit

Compare

this product is listed under import category.
shipping time is 1-2 weeks.

Rs.7,999.00 Rs.7,499.00

Categories: , ,

Description

APM 2.8 ArduPilot UAV Flight Controller Ublox Neo-6M GPS PM 915Mhz

  • Features:
  • Introduction:
    This is the new APM 2.8 autopilot module. The sensors are exactly the same as with APM2.6, however this version have an onboard compass, which makes this version ideal for use with multicopters and rovers.
  • Features :
    Arduino Compatible
    Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer
    Onboard 4 MegaByte Dataflash chip for automatic datalogging
    Optional off-board GPS, uBlox LEA-6H module with Compass.
    One of the first open source autopilot systems to use Invensense’s 6 DoF Accelerometer/Gyro MPU-6000.
    Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
    Atmel’s ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively.
  • GPS Features:
    – Built-in compass GPS module
    – Main chip: Ublox-6M
    – With fast satellite searching speed and high precision
    – Compatible with APM serial port and I2C port
    – Includes round plastic shell and GPS support
  • 3DR Radio Telemetry Kit 915Mhz
  • Description:
    The 3DRobotics 3DR Radio is the ideal way to setup a telemetry connection between your APM and a ground station. Small, inexpensive and with great range, the 3DR radio uses an open source firmware which allows us to do things that cannot be done with other radios.
  • Radio Features:
    – Very small size
    – Light weight (under 4 grams without antenna)
    – Available in 915MHz
    – Receiver sensitivity to -121 dBm
    – Transmit power up to 20dBm (100mW)
    – Transparent serial link
    – Air data rates up to 250kbps
    – Range of approx 1 mile
    – MAVLink protocol framing and status reporting
    – Frequency hopping spread spectrum (FHSS)
    – Adaptive time division multiplexing (TDM)
    – Support for LBT and AFA
    – Configurable duty cycle
    – Built in error correcting code (can correct up to 25% data bit errors)
    – Demonstrated range of several kilometers with a small omni antenna
    – Can be used with a bi-directional amplifier for even more range
    – Open source firmware
    – AT commands for radio configuration
    – RT commands for remote radio configuration
    – Adaptive flow control when used with APM
    – Based on the HopeRF HM-TRP radio modle, featuring an SiLabs Si1000 RF microcontro
  • MAVLink-OSD V2.0
  • Introduction:
    – MAVLink-OSD is an Arduino based project and it is fully compatible with original MinimOSD.
    – This board can be used for CRIUS AIOP and Arduflyer / ArduPilot-Mega.
    – MAVLink-OSD with switching DC/DC stepdown powersupply to maximize efficiency on power system. No more heating problems when using this OSD board.
    – Default OSD Firmware is MinimOSD-Extra, written by Gábor Zoltán.
    – About how to use the configurator tool to setup OSD function: Click here
    – How to setup hardware (original MinimOSD Wiki): click here
    Power Module is a simple way of providing your APM/Arduflyer with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6P cable. The on-board switching regulator outputs 5.3V and a maximum of 3A from up to a 7S LiPo battery.
    Note: The Power Module is only designed to power APM/Arduflyer, a RC receiver and accessories (GPS, Radio telemetry). It is not designed to power servos. Use your aircraft’s own ESC/BEC for that.
  • Hardware Features:
    – ATMEGA328P Microcontroller
    – MAX7456-EUI monochrome on-screen display
    – 5V/500mA DC/DC regulator for MAX7456-EUI
    – Operating voltage: 5V(FTDI connector) and 12V(Video I/O connector)
    – Supported NTSC & PAL
    – FTDI connector
  • Software features:
    – Full MAVLink protocol support
    – Graphical configurator tool
  • APM Arduflyer Power Module V1.0
  • Introduction:
    Power Module is a simple way of providing your APM/Arduflyer with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6P cable. The on-board switching regulator outputs 5.3V and a maximum of 3A from up to a 7S LiPo battery.
    Note: The Power Module is only designed to power APM/Arduflyer, a RC receiver and accessories (GPS, Radio telemetry).It is not designed to power servos. Use your aircraft’s own ESC/BEC for that.
  • Features:
    – Max input voltage: 30V
    – Max current sensing: 90A
    – Voltage and current measurement configured for 5V ADC
    – Switching regulator outputs 5.3V and 3A max
    – 6P molex cable plugs directly to APM/Arduflyer 2.5’s ‘PM’ connector

s-l1600 (3) s-l1600 (4) s-l1600 (5) s-l1600 (6) s-l1600 s-l500 s-l1600 (1) s-l1600 (2)

Reviews

There are no reviews yet.

Be the first to review “APM 2.8 ArduPilot UAV Flight Controller Ublox Neo-6M GPS PM 915Mhz 3DR Kit”

Your email address will not be published. Required fields are marked *